New Search

Find Your Dream Home

Search Error

Multiple MLS Listings

Price Range

Minimum
Maximum

Bed & Bath

Bedrooms: All
Bathrooms: All

Remodeling

How to Install Drywall

Hanging drywall is an important step when finishing a room. Learn some solid techniques to use when you start your drywall project. 

Courtesy of Better Homes and Gardens®

Project preparation

One of the most important pieces of advice to remember when piecing together drywall is to take your time. Rushing will only lead to potential gaps and mistakes. By using the correct technique and learning how to install drywall properly, you can save money by doing the work yourself and also do it quickly.

1. Nail or screw according to code

Local building codes specify how many nails or screws you should use to hang drywall and in what sort of pattern. Codes vary not only from region to region, but from room to room; for example, more fasteners may be required in bathrooms. Check with your building department.

How to Install Drywall 
Many professionals don't nail in pairs, but there is good reason to do so: If one nail pops through the paper, the other will hold.

For ceiling panels, the general practice is to pair nails at 12-inch intervals around the perimeter and 12 inches along each joist. Requirements are less stringent for walls. If you don't use adhesive, install two nails into the wall studs at 16-inch intervals and a single nail every 7 inches along edges. When using adhesive, install two nails at 24-inch intervals and one nail at 7 inches along the edge. Keep adhesive 6 inches away from top and bottom of sheet.

1a. Setting nailheads correctly

If you simply drive in a nail flush, you will not be able to cover over it with joint compound. If you drive the nail too deeply, you will break the paper on the drywall. When the paper is broken, the nail won't hold; it tears right through the gypsum inner core.

Try to drive the nail so the nailhead is set into a slightly dimpled surface. No portion of the nailhead should protrude above the surface of the drywall.

To test if your nails are driven deeply enough, run a taping blade along the surface of the wall. You should not feel any nailheads click against the blade as you pull it across. Pull out any nails that miss a joist or stud. Swat the hole with your hammer to dimple it.

How to Install Drywall

1b. Attaching drywall with screws

If you are using screws, the same principles apply as with nailing: The screw head must be set below the surface, but it must not break the paper. This is difficult to do with a simple screwdriver bit. Use a dimpler bit or a drywall screwdriver (see Tool Tip Box). Always drive in screws perpendicular to the sheet or their heads will tear the paper.
How to Install Drywall

2. Install the ceiling sheets

Hang drywall on the ceiling before installing the wall sheets. Start in a corner and against one side of the room and work out from there, keeping the panels perpendicular to the joists. Take time before you start to locate joists and mark their locations on the sheet and the wall. Searching for joists while holding the sheet up with your head is no fun.

The quickest, but most difficult, way to install drywall on a ceiling is to set the panel in place and support it with your head, leaving your hands free to hold and drive nails or screws. Wearing a baseball cap greatly minimizes pulled hair and a sore head.

To make things easier, construct one or two 2x2 T-braces to use as props. Or, rent a drywall hoist. Either solution will make the process easier and result in a much neater job.
How to Install Drywall

3. Install the wall sheets

Once the ceiling panels are up, hang sheets on the walls. If you are installing sheets horizontally, begin with the upper sheets, butting them firmly against the ceiling drywall. Make sure all vertical seams hit studs. Butt the lower panels firmly against the upper panels, tapered edge to tapered edge. Raise up sheets tightly with a wedge or lever.

If you are installing sheets vertically, check the tapered edges to make sure they fall midway across a stud. If they don't, either cut the drywall or attach pieces of lumber to the stud to give yourself a nailing surface for the next piece.

Overlap pieces at corners, as shown above. Finish the job by adding the filler pieces, measuring and cutting each piece to size. Make sure each piece has at least two nailing members to support it.

How to Install Drywall

Your Opinion

Conducting a property search may direct you to a Web site that is owned and operated by a Better Homes and Gardens® Real Estate brokerage. The site will contain local listing information that meets your search criteria. Different terms of use and privacy policies will apply.

© Copyright 2014, Better Homes and Gardens Real Estate LLC.

All Rights Reserved. Better Homes and Gardens® is a registered trademark of Meredith Corporation licensed to Better Homes and Gardens Real Estate LLC. An Equal Opportunity Company. Equal Housing Opportunity. Each Better Homes and Gardens Real Estate office is independently owned and operated.